Langsung ke konten utama

Tugas 6 Jarkom 3 Teori ( Konfigurasi OSPF )

Konfigurasi OSPF


Nama:Nor Budi Cahyono
NIM: 09.240.0022
Kelas: 4M41




OSPF (Open Shortest Path First IGP) merupakan sebuah routing protokol berjenis IGP (interior gateway routing protocol) yang hanya dapat bekerja dalam jaringan internal suatu ogranisasi atau perusahaan. Jaringan internal maksudnya adalah jaringan di mana Anda masih memiliki hak untuk menggunakan, mengatur, dan memodifikasinya.


Atau dengan kata lain, Anda masih memiliki hak administrasi terhadap jaringan tersebut. Demikian adalah pengantar untuk jaringan OSPF, namun disini ane bukan mau berkoar tentang OSPF tapi pengen berbagi cara penggunaan dan setting untuk jaringan OSPF, berikut adalah :


pengaturan router0
======================
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 10.10.10.1 255.255.255.0
Router(config-if)#no shu
Router(config-if)#ex

Router(config)#int ser2/0
Router(config-if)#ip add 192.168.10.2 255.255.255.252
Router(config-if)#no shu
Router(config-if)#ex

Router(config)#int ser3/0
Router(config-if)#ip add 192.168.10.10 255.255.255.252
Router(config-if)#clock rate 9600
Router(config-if)#no shu
Router(config-if)#ex

Router(config)#router ospf 1
Router(config-router)#network 10.10.10.0 0.0.0.255 area 0
Router(config-router)#network 192.168.10.0 0.0.0.3 area 0
Router(config-router)#network 192.168.10.8 0.0.0.3 area 0
Router(config-router)#ex

Router(config)#int ser2/0
Router(config-if)#band
Router(config-if)#bandwidth 1
Router(config-if)#no shu
Router(config-if)#ex

Router(config)#int ser3/0
Router(config-if)#band
Router(config-if)#bandwidth 9
Router(config-if)#no shu
Router(config-if)#ex
Router(config)#

pengaturan router1
==================

Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.17 255.255.255.240
Router(config-if)#no shut
Router(config-if)#ex

Router(config)#int se2/0
Router(config-if)#ip add 192.168.10.1 255.255.255.252
Router(config-if)#no shut
Router(config-if)#ex

Router(config)#int ser3/0
Router(config-if)#ip add 192.168.10.5 255.255.255.252
Router(config-if)#clock rate 9600
Router(config-if)#no shut
Router(config-if)#ex

Router(config)#router ospf 1
Router(config-router)#network 192.168.10.0 0.0.0.3 area 0
Router(config-router)#network 172.16.1.16 0.0.0.15 area 0
Router(config-router)#network 192.168.10.4 0.0.0.3 area 0
Router(config-router)#ex

Router(config)#int ser 2/0
Router(config-if)#bandwidth 1
Router(config-if)#no shu
Router(config-if)#no shutdown
Router(config-if)#ex
Router(config)#int ser3/0
Router(config-if)#band
Router(config-if)#bandwidth 5
Router(config-if)#no shu
Router(config-if)#ex
Router(config)#

Pengaturan Router2
==================
Router>en
Router#conf t
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.33 255.255.255.248
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#int se3/0
Router(config-if)#ip add 192.168.10.6 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#int se2/0
Router(config-if)#ip add 192.168.10.9 255.255.255.252
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#router ospf 1
Router(config-router)#network 172.16.1.32 0.0.0.7 area 0
Router(config-router)#network 192.168.10.4 0.0.0.3 area 0
Router(config-router)#network 192.168.10.8 0.0.0.3 area 0
Router(config-router)#exit

Router(config)#int se3/0
Router(config-if)#bandwidth 6
Router(config-if)#no sh
Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#bandwidth 10
Router(config-if)#no shu
Router(config-if)#ex
Label:

Komentar

Posting Komentar

Postingan populer dari blog ini

LM386 AUDIO AMPLIFIER CIRCUIT

The integrated chip LM386 is a low power audio frequency amplifier requiring a low level power supply (most often batteries). It comes in an 8-pin mini-DIP package. The IC is designed to deliver a voltage amplification of 20 without external add-on parts. But this voltage gain can be raised up to 200 (Vu = 200) by adding external parts. LM386 audio amplifier circuit diagram The external parts shown on diagram 3.1 can be selected to get the desired gain. Circuit A will give a voltage amplification of 200. Circuit B will give a gain around 50. The circuit C is not for voltage amplification but will raise the bass level by about 5 dB. Take note that the circuit C is to be connected between pins 1 and 5 of the IC. The power output is around 550 mW at 16 ohm speaker impedance. This audio frequency amplifier is ideal for small battery powered devices. If you use the external circuit A, replace the Rx with a jumper wire in the PCB. If you use the external circuit C, solder the additio...
Posting Komentar
Baca selengkapnya

OpenOffice.org 3.4.0 Beta 1

OpenOffice.org   is the   open-source   office  software   for word processing , spreadsheets ,   presentations ,   graphics ,   databases   and   much more.   This  application is   available   in   many languages   ​​and   works on   all computers .   These  applications store   your data on   an international   open standard   format   and   are also   able to read /   write files   from   another   office   package .   This  application   has the ability multiplatform   and   can   be used   in many   good   Operating   System , Microsoft Windows ,   Linux and   Macintosh . In addition   OpenOffice.org   can be  downloaded   and used   without any   licensing fees .   OpenOffice.org   is released under   the LGPL licens...
Posting Komentar
Baca selengkapnya